After a harvest season that runs from corn and rice in August to soybeans in October or later, everyone is ready to park the combine and walk away. But don't throw in the towel just yet. Your combine needs a bit of work before it's stored for the winter. Leftover grain, chaff, and crop residue attract rodents and insects, trap moisture against metal, and become a fire risk the next time the engine runs hot. Taking care of it now can save you from problems in the spring. Here's the checklist we recommend before your combine sits for the off-season.
Safety always comes first. Before you start your cleaning and maintenance, put your combine in park on firm, level ground. Lower the header to the ground or onto its header trailer. If the feeder house has to stay raised for any reason, engage the feeder house lift cylinder safety stop. Never work under a raised header that is held up only by hydraulics. Disengage the separator and header drives and engage the parking brake. Finally, shut off the engine, remove the key, and wait for all moving parts to stop completely.
Crop debris, dust, and chaff cause major problems for combines that sit idle. They not only lead to rust and potential fires but also attract rodents that nest in your equipment and chew wires for fun. A thorough cleaning of the interior and exterior can prevent this damage.
Just a few pounds of grain can be enough to draw rodents looking for their next meal. Unload every last bushel, then open the cleanout doors on the grain tank sump, clean grain elevator, tailings elevator, and unloading auger to clear leftover grain. Then open and empty the rock trap.
Dry chaff near hot surfaces is a leading cause of combine fires, and buildup holds moisture that leads to rust. Clear all of this away with compressed air or a leaf blower, working from the top down and front to back. Focus on the engine compartment, the radiator and cooler package, the area around the exhaust, wiring harnesses, and bearings. Wear eye protection and a dust mask while completing this step.
The last thing you want is leftover garbage from the season to become an invitation for pesky mice and other rodents. Remove any trash from your cab, vacuum floors and seats, and wipe down controls and the display. Clean or replace the cab fresh-air and recirculation filters.
Pressure washing always comes after your blowout. If done in reverse, water turns dry chaff into packed mud, which makes more of a mess than you started with. Use low pressure and a wide fan tip around bearings, seals, electrical connectors, decals, and radiator fins. High pressure forces water into places it shouldn't go. Let the machine dry completely before storage. Louisiana humidity slows drying, so leave doors open or park it in the sun. Grease all fittings after washing to push out trapped water. Rice harvest often leaves heavy mud on tracks, tires, and the undercarriage, so those areas need extra attention.
The off-season is the best time to find any problems with your equipment so you can order parts early instead of during the spring rush. Catching a worn belt or thin auger flighting now gives you all winter to fix it. That beats finding it the week you need to start cutting. Keep a notepad or your phone handy as you go. Anything you'd want replaced before next season goes on the list.
Check every belt for cracks, fraying, and glazing. Glazing is a shiny, hardened surface that slips under load. Look over chains for stretch, stiff links, and sprockets with hooked or pointed teeth. Clean the chains and coat them with oil to keep rust from setting in while the machine sits. Your operator's manual may also recommend loosening belt tension for storage.
Grain wears metal down over time. Look for thin or worn flighting on the augers. Check liners and housings for holes or soft spots. Inspect the elevator paddles and chains, and check chain tension while you're in there.
Inspect the rasp bars, concaves, rotor or cylinder, separator grates, chaffer, and sieves. Look for wear, bent wires, cracks, and missing hardware. If you ran rice this year, take a closer look. Rice is hard on threshing and cleaning parts, so those machines often wear out faster.
Change the engine oil and filter before storage. Used oil carries acids and moisture that can corrode engine parts over the winter. Check the hydraulic fluid, gearbox oil, and coolant levels, and test the coolant's strength. Our winters are mild, but North Louisiana still sees hard freezes. While you're at it, replace the fuel filters and inspect the engine air filter.
Fill the fuel tank before storage. A full tank leaves less room for air, which means less condensation. That matters with Louisiana humidity. Add a diesel fuel stabilizer, and consider a biocide to prevent microbial growth. Then run the engine for a few minutes so the treated fuel moves through the system. If your combine uses diesel exhaust fluid, check the manual for storage guidance. DEF breaks down with heat and time.
Inflate tires to the recommended pressure. Check for cuts, bulges, and cracks in the sidewalls. If you can, block up the axles to take weight off the tires during storage, and keep them out of direct sunlight. On track machines, check track tension and wear instead.
Without proper storage, all your hard work from the previous steps goes to waste. Follow these instructions to protect your investment while it hibernates until the next harvest.
Indoor storage in a dry, ventilated shed or barn is always the best option. If the combine has to stay outside, use a breathable cover and park on gravel or concrete rather than bare dirt, since dirt wicks moisture up into the machine. Cover the exhaust stack and air intake to keep out birds, mud daubers, and wasps. Set rodent bait stations or traps around the machine, not inside the cab, and check them monthly. Store the header separately on its trailer or on blocks.
Cold weather can be harsh on batteries. Prevent drain and damage by disconnecting the battery, negative terminal first. Clean the terminals with a baking soda and water solution. Store the battery fully charged in a cool, dry place, or keep it on a maintenance charger. Check the charge monthly. Louisiana heat speeds up self-discharge, and a discharged battery is more likely to freeze during a cold snap.
Some repairs need more than a grease gun or a good pressure wash. When it comes to rotor and concave work, bearing replacement, electrical issues, and precision ag troubleshooting, it's best to let certified service professionals take care of the job. At Goldman Equipment, we offer factory-trained technicians, genuine John Deere parts, and service locations across North and Central Louisiana. Scheduling an inspection or repair now during the off-season lets you beat the spring rush and get your combine field-ready well ahead of the next harvest.
At Goldman Equipment, we're here to help your operation in every season. For more information on parts, service, or off-season maintenance, reach out to your nearest location today.
Start by removing everything that draws rodents in. Unload every last bushel, clear leftover grain from the elevators, augers, and sump, and take all trash out of the cab. Once the combine is in storage, set bait stations or traps around the machine, not inside the cab, and check them monthly.
Yes. Change the engine oil and filter before storage. Used oil carries acids and moisture that can corrode engine parts over the winter. While you're at it, check the hydraulic fluid, gearbox oil, and coolant levels, and replace the fuel filters.
Yes, as long as you blow it out first and use care around sensitive parts. Use low pressure and a wide fan tip around bearings, seals, electrical connectors, decals, and radiator fins. Let the machine dry completely, then grease all fittings to push out trapped water.
Yes. Fill the fuel tank to limit condensation, which matters with Louisiana humidity. Add a diesel fuel stabilizer, and consider a biocide to prevent microbial growth. Then run the engine for a few minutes so the treated fuel moves through the system.
Check belts and chains, augers and liners, threshing components, fluids and filters, and tires. Keep a list as you go so you can order parts early instead of during the spring rush. If you ran rice, give the threshing and cleaning parts a closer look, since rice is hard on them.
Disconnect the battery, negative terminal first, and clean the terminals with a baking soda and water solution. Store it fully charged in a cool, dry place, or keep it on a maintenance charger. Check the charge monthly, because Louisiana heat speeds up self-discharge.